Splicing Machines

Product Details:

The Fujikura 80C+ is a fully ruggedized, core alignment fusion splicer, providing consistent, low loss, splice performance. The new design streamlines the steps required to complete splices, resulting in greater productivity. “Configurable automation” features allow you to customize the operation of the machine to best suit your particular splicing technique and process. A new programmable “automatic wind protector” closes and begins the splicing process after clamping the fibers in position or pressing the “set” button. Once the splice is completed, not only is the wind protector opened but one of the sheath clamps, you decide which, is automatically raised making removal of the fibers fast and easy! Similarly, the "clamshell" design of the tube heater clamps the splice protection sleeve and applies heat from both sides which results in a reduced shrink time of just 9 seconds.
Features:

• Automatic and fully programmable wind protector.
• Li-Ion battery with 200 splices/shrinks per charge.
• 9-second tube heater.
• High capacity Lithium-Ion battery pack (200 splices/shrinks)
• Internet software upgrades.
• 5 mm cleave length for splice on the connector or small package needs.
• Fully ruggedized for shock, dust, and moisture.
• Onboard training and support videos.
• Multi-function transit case with the integrated workstation.

Product Details:

The Fujikura 70RC Fusion Splicer is equipped with a precision, fixed v-groove for splicing single fibers or ribbon fiber up to 12 fibers. Incorporating the proven ruggedized features pioneered by Fujikura, it has added automated and enhanced user control features to increase splicing efficiency. A user programmable, automated wind protector expedites the splicing process by automatically closing to initiate the splicing process and opening upon splice completion. A new auto-start “clamshell design” tube heater applies heat to both sides of the splice protection sleeve resulting in a 40-second shrink time for a 12-fiber ribbon. The result is a total splice process time of approximately 55 seconds! Ruggedness and durability are greatly enhanced by a mirror-less optical system and "severe-impact resistant" monitor. Battery capacity is now 110 splices/shrinks. An innovative transit case doubles as a built-in or mobile workstation and makes splicing easier than ever before.

Features:
• Automated and programmable wind protector.
• 40-second automated tube heater.
• Fully ruggedized for shock, dust, and moisture.
• Li-ion battery with 110 splices/shrinks per charge.
• Onboard training and support videos.
• Internet software upgrades.
• Multi-function transit case with an integrated workstation.

Other Details :

• Model FSM-70RC Fusion Splicer
• Applicable Fibers Single-mode (G.652 & G.657), Multimode (G.651), DS (G.653), NZDS (G.655)
• Fiber Count Single, 2, 4, 5, 6, 8, 10, 12
• Coating Diameter Ribbon: 0.25 mm to 0.4 mm, Single: 250 µm and 900 µm
• Typical Average Splice Loss 0.05 dB with SM, 0.02 dB with MM, 0.08 dB with DS, 0.08 dB with NZDS; measured by cut-back method relevant to ITU-T and IEC standards
• Arc Calibration Method Automatic, real-time by using results of the previous splice when in AUTO mode, manual arc calibration function available
• Splicing Modes 100 preset and user programmable modes
• Splice Loss Estimate Based upon dual camera cladding alignment data
• Fiber Display X or Y, or both X and Y simultaneously; front or rear monitor display options with automatic image orientation
• Magnification 35X to 90X
• Viewing Method Dual cameras with 4.7 inch TFT color LCD monitor with anti-reflective coating
• Operating Condition 0 to 3,660 m above sea level, 0 to 95% RH, and -10 to 50°C respectively
• Tube Heater Built-in tube heater with 30 heating modes; auto-start function
• Tube Heating Time Typical 40 seconds with FP-5 sleeve, 17 seconds with FP3 (40), 5-15 seconds with Fujikura micro sleeves
• Protection Sleeve Length 60 mm, 40 mm, Micro
• Splice/Heat Cycles with Battery Typical 110 cycles with power save functions activated
• Power Supply Auto voltage selection from 100 to 240V AC or 10 to 15V DC with ADC-13, 13.2V DC with BTR-08 battery
• Terminals USB 1.1 (USB-B type) for PC communication, Mini-DIN (6-pin) for HJS-02/03 and SH-8 tube heater
• Wind Protection Maximum wind velocity of 15m/s (34 mph)
• Dimensions 146 W x 159 D x 150 H (mm) / 5.7 W x 6.3 D x 5.9 H (inches)
• The weight of AC adapter: 2.5 kg (5.5 lbs) with battery

Additional Information:

• Item Code: FSM-70R
• Pay Mode Terms: T/T (Bank Transfer)

Product Details:

The Fujikura 62C+ Optical Fiber Fusion Splicer core alignment model fusion splicer provides low loss splice results without adding more expensive automated features. A conventional flip open style wind protector and non-motorized tube heater reduce the complexity of the splicer without substantially increasing total cycle time. Fully rugged for shock, dust, and moisture.

Additional Information:

• Item Code: Fujikura-62C
• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: New Delhi
• Delivery Time: 1 week

Product Details:

The new FSM-50S Fusion Splicer's leading-edge features, including unprecedented size, weight, and ruggedness, make it the first core-alignment splicer truly optimized for field use, including FTTH applications. Automation such as calibration-free arc (with AUTO splice mode), automatic fiber identification and reduced operational steps, provides ease of use. In addition, the FSM-50S offers increased flexibility with user selectable front or top monitor positioning. The FSM-50S splicer has been designed for use in harsh, outdoor conditions and features an innovative wind protector, which allows splicing in 30 mph cross winds.

Features

Automatic core to core, low-loss splicing regardless of fiber quality or age

9 second splicing time

35 second heat time

Wind protector design withstands 30 mph cross wind

User selectable monitor position

Excellent visibility in bright sunlight with 5.6" TFT Color LCD display

Multiple pre-programmed modes for specialized splicing

Optional data download kit to connect splicer to PC

Additional Information:

• Item Code: 50S
• Pay Mode Terms: T/T (Bank Transfer)
• Port of Dispatch: Delhi
• Delivery Time: 1 week

Product Details:

The Fujikura 22S Fusion Splicer is designed for high-end FTTH splicer applications in FTTX, Data Center / LAN, and Access Networks. It offers an active V-Groove alignment single fiber splicer for reliable and improved splicing performance for a range of different fibers; SMF, MMF, DSF, NZDSF. it is applicable from 125μm cladding diameter/up to 3mm sheath diameter fibers with sheath clamp. It produces an automated tube-heating time of 30 seconds (single mode 60mm).
Applications and Fibres:

• FTTX,FTTH
• Singe-Mode Fibre, Multi-mode Fibre, Dispersion-Shifted Fibre (DSF), Non-Zero Dispersion-Shifted Fibre (NZDSF).

Additional Information:

• Port of Dispatch: New Delhi

Product Details:

Two camera, active cladding alignment
• 5" touchscreen monitor 
• Interchangeable sheath clamps and fiber holders 
• Fully ruggedized for shock, moisture and dust resistance 
• Extended-life electrodes, 5,000 splices, exchangeable without tools
• Long-life battery (200 splices/shrinks per charge).

Additional Information:

• Delivery Time: Ex-stock